 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Features +35 dBm Input IP3 Conversion Loss: 8.8 dB No External Components Ultra Small MSOP Package: 14.8mm2 Typical Applications High Dynamic Range Infrastructure: * GSM, GPRS & EDGE * CDMA & W-CDMA * Cable Modem Termination Systems Functional Diagram General Description The HMC400MS8 is a high dynamic range passive MMIC mixer in a plastic surface mount 8 lead Mini Small Outline Package (MSOP) covering 1.7 to 2.2 GHz. Excellent input IP3 performance of +36 dBm for down conversion and +29 dBm for up conversion is provided for 2.5G & 3G GSM/CDMA based UMTS or PCS applications at an LO drive of +17dBm. With a 1dB compression of +21 dBm, the RF port will accept a wide range of input signal levels. Conversion loss is 8.5dB typical and LO isolations are maintained at 22 to 33 dB. This miniature singleended monolithic GaAs FET mixer does not require any external components or bias. The 50 to 300 MHz IF frequency response will satisfy many UMTS/PCS transmit or receive frequency plans configured for low side LO. The HMC400MS8 input IP3 performance coupled with its high P1dB rivals traditional active FET mixers while offering a much smaller 14.8mm2 standard IC footprint and no DC bias. 12 MIXERS - SMT Electrical Specifications, TA = +25C, LO = +17dBm, IF = 200 MHz* Parameter Frequency Range, RF Frequency Range, LO Frequency Range, IF Conversion Loss Noise Figure (SSB) LO to RF Isolation LO to IF Isolation IP3 (Input) 1 dB Gain Compression (Input) LO Input Drive Level (Typical) 29 16 30 18 Min. Typ. 1.7 - 1.8 1.4 - 1.75 DC - 300 9 9 33 20 34 21 +16 to +18 11 11 24 17 32 18 Max. Min. Typ. 1.8 - 2.0 1.5 - 1.95 DC - 300 8.8 8.8 30 22 36 21 +16 to +18 10.5 10.5 20 19 28 18 Max. Min. Typ. 2.0 - 2.2 1.7 - 2.15 DC - 300 8.8 8.8 25 25 32 22 +16 to +18 10.5 10.5 Max. Units GHz GHz MHz dB dB dB dB dBm dBm dBm *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. 12 - 212 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Conversion Gain vs. Temperature @ LO = +17 dBm 0 Isolation @ LO = +17 dBm 0 RF TO IF LO TO RF CONVERSION GAIN (dB) -5 ISOLATION (dB) -10 LO TO IF -10 -20 + 25C -15 + 85C - 40C -30 -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -40 1.7 1.8 1.9 2 2.1 2.2 2.3 FREQUENCY (GHz) 12 MIXERS - SMT Conversion Gain vs. LO Drive 0 Return Loss @ LO = +17 dBm 0 -5 CONVERSION GAIN (dB) RETURN LOSS (dB) -5 -10 -15 RF LO -10 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm -20 -25 -15 -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -30 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Upconverter Performance Conversion Gain @ LO = +17 dBm 0 If Bandwidth @ LO = +17 dBm 0 CONVERSION GAIN RETURN LOSS CONVERSION GAIN (dB) -5 RESPONSE (dB) -5 -10 -10 -15 -15 -20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 -20 50 100 150 200 250 300 350 400 450 500 IF FREQUENCY (MHz) *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 213 v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Input IP3 vs. IF Frequency, RF = 1.75 GHz 40 Input IP3 vs. Temperature, LO = +17 dBm 40 35 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 30 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm 30 + 25C + 85C - 40C 25 25 12 MIXERS - SMT 20 60 90 120 150 180 210 240 270 300 IF FREQUENCY (MHz) 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Input IP3 vs. IF Frequency, RF = 1.95 GHz 40 Input IP3 vs. LO Drive 40 35 35 INPUT IP3 (dBm) INPUT IP3 (dBm) 30 LO = +15dBm LO = +16dBm LO = + 17dBm LO = + 19dBm 30 + 15dBm + 16dBm + 17dBm + 19dBm 25 25 20 60 90 120 150 180 210 240 270 300 IF FREQUENCY (MHz) 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 Input IP3 vs. IF Frequency, RF = 2.15 GHz 40 Upconverter IP3 vs. LO Drive, IF = 200 MHz 40 35 35 30 LO = +15dBm LO = +16dBm LO = +17dBm LO = +19dBm INPUT IP3 (dBm) INPUT IP3 (dBm) LO = +15dBm LO = +16dBm LO = +17dBm LO = + 19dBm 30 25 25 20 60 90 120 150 180 210 240 270 300 IF FREQUENCY (MHz) 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 214 v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Input IP2 vs. Temperature @ LO = +17 dBm 45 Input IP2 vs. LO Drive @ LO = +17 dBm 45 40 40 INPUT IP2 (dBm) INPUT IP2 (dBm) 35 35 30 + 25C + 85C - 40C 30 + 15 dBm + 16 dBm + 17dBm + 19dBm 25 25 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 20 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 12 MIXERS - SMT 12 - 215 Input P1dB vs. Temperature @ LO = +17 dBm 25 24 23 MxN Spurious Outputs nLO mRF 0 1 2 + 25C + 85C - 40C 0 xx 9 71 79 77 1 -11 0 70 80 80 2 7 24 49 80 80 3 4 31 58 79 79 4 8 27 64 77 80 INPUT P1dB (dBm) 22 21 20 19 18 17 16 15 1.7 1.8 1.9 2 2.1 RF FREQUENCY (GHz) 2.2 2.3 3 4 RF Freq = 2 GHz @ -10 dBm LO Freq = 1.8 GHz @ +17 dBm All values in dBc relative to the IF output power. Harmonics of LO nLO Spur @ RF Port LO Freq (GHz) 1.4 1.55 1.7 1.85 2 2.15 1 42 33 29 26 24 21 2 26 25 29 31 36 38 3 56 56 49 44 44 43 4 Absolute Maximum Ratings RF/IF Input LO Drive 46 53 50 53 48 49 Storage Temperature Operating Temperature IF DC Current -65 to +150 C -40 to +85 C 40 mA +27 dBm +27 dBm LO = +17 dBm All values are in dBc below input LO level @ RF port. *Unless otherwise noted, all measurements performed as a downconverter, with low side LO & IF = 200 MHz. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Outline Drawing 12 MIXERS - SMT NOTES: 1. PACKAGE BODY MATERIAL: LOW STRESS INJECTION MOLDED PLASTIC SILICA AND SILICON IMPREGNATED. 2. LEAD MATERIAL: COPPER ALLOY 3 LEAD PLATING: Sn/Pb SOLDER 4. DIMENSIONS ARE IN INCHES [MILLIMETERS] 5. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.15mm PER SIDE. 6. DIMENSION DOES NOT INCLUDE MOLDFLASH OF 0.25mm PER SIDE. 7. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO THE PCB RF GROUND Pin Descriptions Pin Number Function Description Interface Schematic 1 LO This pin is AC coupled & matched to 50 Ohms from 1.4 to 2.2 GHz. Blocking capacitors are required if line potential is not equal to 0V. 2, 4 N/C Not connected. 3, 6, 7 GND This pin must be connected to RF ground. 5 IF Port This pin is DC coupled. For applications not requiring operation to DC this port should be DC blocked externally using a series capacitor. Choose value of capacitor to pass IF frequency desired. For operation to DC, this pin must not sink/source more than 40 mA of current or failure may result. 8 RF Port This pin is DC coupled & matched to 50 Ohm from 1.7 to 2.2 GHz 12 - 216 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com v01.1003 MICROWAVE CORPORATION HMC400MS8 HIGH IP3 GaAs MMIC MIXER, 1.7 - 2.2 GHz Evaluation PCB 12 MIXERS - SMT Description PC Mount SMA RF Connector HMC400MS8 Mixer 101828 Eval Board List of Material Item J1 - J3 U1 PCB* * Circuit Board Material: Rogers 4350 The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of VIA holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 12 Elizabeth Drive, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order Online at www.hittite.com 12 - 217 |
Price & Availability of HMC400MS8
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |